DJI Mavic Pro/Platinum Float Kit with hard smooth Styrofoam floats.

Out of stock
Product Details

Kits shipping with new designed rear brackets displayed in picture below. Instructions

Current kits come with new Rear mounts like in this picture.

Current Order shipping time one weeks.

NOTE: These are handmade, 3D-printed parts or craft styrofoam. They may have cosmetic imperfections, which will not affect their performance.
Brackets maybe black, gray or white.

You can download a copy of theinstructions here for free:

I have been looking for a good way to launch my Mavic Pro from my sit on top Kayak, when at a Central Florida Mavic Facebook group meet up I saw a Mavic on floats. It worked okay, however I didn’t like the way the floats were mounted, and that it didn't sit or take off level from the water. So, I set out designing my own mounts which I printed on my 3d printer.
Besides water this kit is great for soft terrain like sand, snow, grass,....

Drones in video using the old style rear bracket.


  • Why 4 Styrofoam balls instead of 2 aerodynamic floats like an airplane uses.
    • Styrofoam balls are lighter, and never leak
    • Four spheres spread out in the water will handle waves better than 2 floats
    • Floats used on airplanes are hydrodynamic designed with a step to help the airplane get up to speed for takeoff and spray guards to prevent water from splashing into the prop while the plane is operating as a boat. Mavics take off and land straight up and down. They do not need a hydrodynamic float to reach take off speed
  • Doesn’t this kit defeat the portability?
    • The whole float kit can be installed or uninstalled in less than a minute. Take it leave it your choice when you head out to fly. Mavic still portable when needed and you can bring a second bag if you feel the need to bring the float kit with you.
    • Note on portability. My other float kit with 3d printed soft squishy floats will squeeze to have their normal size for transport.
  • How much of the float gets in the camera view?
    • Only with the camera pointed straight down under very hard left or right direction change the edges of the floats appear in the edges of the frame for a moment. Flying in Tripod mode or similar like you would trying to get smooth footage the floats never appear in the frame.

    Included in the kit:
    · 4of 99mm Tapered Head Screw
    · 4of Flat Washer
    ·2 of Rear Mount brackets. left and right with Velcro straps
    · 1of Rear Sliding Mount/Latch (slipped into the rear mount)
    · 2of Front Mounts· 2of Flexible Retention Bands for the front mounts
    · 4 of99mm Smooth Styrofoam pre-drilled floats
  • NOTE: These are handmade 3D printed parts or craft Styrofoam. They may have cosmetic imperfections, which will not affect their performance.
    1. With the arms extended, lay your Mavic on its back2. With the slip mount pulled out about 10mm, carefully press tab on the fixed end intothe slot in the Mavic rear landing skid.
    3. Slidethe slip mount in while pressing its tab into the slot Mavic rear landing skid.a. Makesure the latch clicks into place
    4. Withthe word FRONT facing the direction the Mavics camera points carefully Slide afront mount onto the Mavic’s front landing leg keeping the Flexible RetentionBand near the top. The nut should be angled out and to the front of the drone.If it is angled back remove it and put it on the other side.
    a. Checkthe window near the base of the mount to make sure it is seated fully on theMavics landing leg.

    NOTE: The nuts on the mounts should beangled slightly forward to provide better water stability. b. Repeat for other front mount.5. Insertthe screws into the predrilled holes on the Styrofoam balls. Push it in untilthe head is flush with the outside of the ball.

    6. Installthe washer on the screw on the other side of the ball7. Threadthe bolt/ball/washer assembly into one of the mounts. You can use a coin tosnug it into place.
  • Caution: Do not over tighten8. Remove floats from brackets for storageor transportation. They should only be bolted to the brackets when you areflying the drone with them.9. Check the tightness of the screws at thebeginning of each flight, including battery changes.
  • Caution:Although this product has been designed around successfully flying on and offvery calm water, we cannot guarantee your Mavic will not receive water damageif you attempt to fly it on or off the water.Warning:There are too many variables we cannot control, including, but not limited to,the calmness of the water, installation of floats, how hard the Mavic lands,etc.
    We are not responsible for any damage to your Mavic.
    Use at your own risk!
    Forsupport or to get replacement parts visit:
Save this product for later